Engine Bolt Torque Size G15A Suzuki Carry Futura Injection 1.5
Engine Bolt Torque Size G15A Suzuki Carry Futura Injection 1.5 - Suzuki Carry's gait and track record has been around for a long time in Indonesia. Even today, the car is still being produced and continues to evolve so that it remains in accordance with the emission regulations determined by the government.
At least, this Suzuki Carry has been present for more than 10 generations. The model is very diverse as well as the series of machines embedded in it. Especially for this article, Ombro will share information about the torque size table for the G15A Suzuki Carry Futura 1.5 injection engine bolt with the body code SL415 which is the ninth generation Suzuki Carry Futura car.
This Suzuki Carry Futura has a twin, the Mitsubishi Colt T120SS, but the engine used is different. Suzuki Carry uses the G15A series engine which is produced by Suzuki itself, as well as the T120SS. It uses a Mitsubishi type 4G15 engine, both with a capacity of 1500cc.
Yes, this G15A engine is a 1500cc inline 4 cylinder engine that is equipped with a multipoint injection system (MPI). This machine is capable of producing a maximum power of 79ps at 5000 rpm. As for the torque, the G15A engine is capable of producing a maximum torque of 120Nm at 5500 rpm. This machine still uses the timing belt as a driver and still requires regular valve adjustment.
4
G15A Suzuki Carry Futura Injection Engine Bolt Size Table 1.5
Fastened Components | Tightening Moment | |
---|---|---|
N.m | 10 | |
11 | ||
12 | 55 | 14 |
Engine mounting frame bracket nuts and bolts | 16 | 9.3 |
Oil pressure switch | 14 | 1.4 |
Oil pump strainer bolt | 11 | 23 |
Oil pump strainer bracket bolt | 11 | 23 |
Drain plug | 50 | 5.0 |
Oil pump plate screw | 11 | 23 |
Oil level gauge guide bolt | 11 | 23 |
Oil pump bolt | 11 | 23 |
Oil pump plug | 23 | 2.3 |
Oil pan nuts and bolts | 11 | 23 |
Timing Belt | ||
CKP sensor bolt | 10 | 1.0 |
stud bolt tensioner | 11 | 23 |
bolt tensioner | 25 | 54 |
Timing belt bolt outside cover | 11 | 23 |
Crankshaft pulley bolt | 16 | 60 |
Crank timing belt pulley bolt | 130 | 13.0 |
Cylinder Head | ||
Camshaft pulley bolt | 60 | 6.0 |
Camshaft housing bolt | 11 | 23 |
Rocker arm shaft bolt | 11 | 23 |
Rocker arm shaft plug | 32 | 76 |
Rocker arm adjusting screw lock nut | 12 | 1.2 |
Cylinder head cover bolt | 11 | 23 |
exhaust pipe bolt | 50 | 5.0 |
CMP sensor case bolt | 11 | 23 |
Cylinder head bolt | 33 → 53 → 0 → 33 → 66 | 3.3 → 5.3 → 0 → 3.3 → 6.6 |
Cylinder Block | ||
Connecting rod bearing cap nut | 35 | 3.5 |
Transmission bolt to cylinder block | 85 | 8.5 |
Transmission nut to cylinder block | 85 | 8.5 |
Transmission stiffener bolt | 50 | 5.0 |
Crankshaft bearing cap bolt (main bearing cap bolt) | 54 | 5.4 |
Rear oil seal housing bolt | 11 | 23 |
Flywheel bolt or drive plate | 76 | 7.6 |
venture plug | 4 | 0.4 |
Notes:
- The torque and bolt tightness values in the table above use Newton meters and Kilogram meters. Pay attention to the value of the torque unit on the Torque Wrench / torque wrench used before tightening. Make sure the units of measure are the same.
- Especially for the Cylinder Head Bolts, the tightening is done sequentially. First, tighten all the bolts by 33Nm, then continue tightening until you get a moment of 53Nm. After that loosen all the existing bolts to 0Nm. Continue tightening all the bolts by 33Nm, and continue until you reach 66Nm.
Read also:
- List of Specifications and Sizes for Mitsubishi T120SS Engine Bolt Tightness
- How to Adjust the Suzuki Carry 1.5 . Car Valve
- Suzuki Carry 1.5 . Car MAP Sensor Check
In carrying out any tightening, especially on Cylinder head bolts, Bearing cap bolts, Connecting rod nuts, always tighten bolts according to the sequence and steps. Errors in performing the tightening steps can damage existing bolts or components.
That's the article about the G15A Suzuki Carry Futura Injection 1.5 Engine Bolt Torque Size that you can convey. Hopefully this article can be useful, thank you